Welcome Guest Search | Active Topics | Log In | Register

USS Constitution Official Build Diary - Pack 10 Options
arpurchase
#1 Posted : 17 June 2018 12:56:39

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsTurquoise Medal: Turquoise Medal for model making know-how contributionOutstanding Build: An award for an outstanding buildBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Registered

Joined: 27/09/2011
Posts: 15,196
Points: 45,687
Location: Dudley
U S S Constitution Pack 10- Stages 91-100

Stage 91 contents:-Carronade parts x 2, thread, eyepins, blocks and pins.

From stages 87,88 and 89 retrieve the bulwark end castings you should have a short pair two long pairs and four medium pairs, one medium pair has a bend. Keeping each set as a pair remove the casting burs and flash from all the parts then undercoat and finally paint all of them yellow ochre.

Take the four medium sets and add the straight pair to the bulwarks at the bow the second bent pair are added to the other end of the bow bulwark making sure the projections on the sides are pointing toward the deck. Next take the four long bulwark ends and glue each pair into the entry ports then add the last two to the stern gunwale making sure both are aligned with each other.

Take a 2 x 6 x 300 ramin strip and cut two pieces from it each 15mm long. Shape both parts into a wedge shape and then paint them with the same green you used on the inner bulwarks. Glue each wedge against the bulwarks below the the entry port.

Stage complete.

Store any unused parts in a labelled bag for future use .
arpurchase attached the following image(s):
P6164783.JPG
P6164789.JPG
P6174790.JPG
P6174795.JPG
P6174796.JPG
P6174798.JPG
P6174800.JPG
P6174801.JPG
P6174803.JPG
P6174805.JPG
P6174808.JPG
P6174809.JPG
P6174812.JPG
P6174815.JPG
P6174817.JPG
P6174818.JPG
P6174822.JPG
Current builds:-C57,Zero, Lamborghini Countach, Caldercraft HMS Agamemnon,Robi,R2-D2, MFH Cobra .

arpurchase
#2 Posted : 18 June 2018 12:27:00

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsTurquoise Medal: Turquoise Medal for model making know-how contributionOutstanding Build: An award for an outstanding buildBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Registered

Joined: 27/09/2011
Posts: 15,196
Points: 45,687
Location: Dudley
Stage 92

Stage 92 contents:- Carronade parts, thread, eyepins, blocks and cleats.

Take the six gun port frets you have saved and remove 30 of the crescent shaped pieces. Sand them all smooth then paint them black. When they are dry start gluing each one above a gun port, starting at the stern and working your way forward attaching 15 per side.

Next cut two 28mm lengths from a 1 x 11 x 300mm ramin strip. Test fit it so its in line with the stem decoration and the the upper white whale when you are happy with the fit paint them black and glue both parts in position on the bow. Now cut four 28mm lengths of 1 x 3 x 300mm ramin sand the pieces and paint them white. Glue each strip to the top and bottom of the strip you just fixed in position making sure everything lines up.

Remove two sets of gun port lids from a fret, sand them then paint them black. When dry paint the outer of each white and then glue them in the closed position in the gap of the white wale at the bow.

Stage complete.

Store any unused parts in a labelled bag for future use .
arpurchase attached the following image(s):
P6174825.JPG
P6174830.JPG
P6174834.JPG
P6174840.JPG
P6174842.JPG
P6174844.JPG
P6174847.JPG
P6174848.JPG
P6174856.JPG
P6174858.JPG
P6174860.JPG
P6174861.JPG
P6184864.JPG
P6184867.JPG
P6184868.JPG
P6184870.JPG
P6184874.JPG
P6184877.JPG
P6184881.JPG
P6184883.JPG
P6184886.JPG
Current builds:-C57,Zero, Lamborghini Countach, Caldercraft HMS Agamemnon,Robi,R2-D2, MFH Cobra .

arpurchase
#3 Posted : 18 June 2018 16:06:44

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsTurquoise Medal: Turquoise Medal for model making know-how contributionOutstanding Build: An award for an outstanding buildBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Registered

Joined: 27/09/2011
Posts: 15,196
Points: 45,687
Location: Dudley
Stage 93

Stage 93 contents:- Carronade parts, thread, eyepins, blocks and deadeyes.

From stage 78 take the gig parts,paint the hull outside white then the inside brown. Next assemble the wooden parts of the gig in the same way you made the other boats in stages 58 and 60 of pack 6.

Stage complete.

Store any unused parts in a labelled bag for future use .
arpurchase attached the following image(s):
P6184889.JPG
P6184893.JPG
P6184897.JPG
P6184899.JPG
P6184901.JPG
P6184903.JPG
Current builds:-C57,Zero, Lamborghini Countach, Caldercraft HMS Agamemnon,Robi,R2-D2, MFH Cobra .

arpurchase
#4 Posted : 19 June 2018 17:33:18

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsTurquoise Medal: Turquoise Medal for model making know-how contributionOutstanding Build: An award for an outstanding buildBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Registered

Joined: 27/09/2011
Posts: 15,196
Points: 45,687
Location: Dudley
Stage 94

Stage 94 contents:- Carronade parts, eyepins, blocks, deadeyes and thread.

At the stern of the ship between the the bulwark ends drill 14 pairs of holes with a 0.75 drill bit the holes closest to the bulwark ends should both be placed 15mm away the other holes should be drilled 20mm apart. Paint 28 eyepins black and then fit them to the holes you just drilled making sure the eyes are in line with the bulwark ends. Now repeat the above on the other side of the ship.

Next at midships drill 4 holes in a central line and spaced evenly apart along the bulwarks on either side of the ship. Paint 8 eyepins black and then glue them into the holes just drilled.

At the bow gunwale drill 8 pairs of holes on either side of the ship. The holes closest to each of the bulwark ends should be 15mm away and the others 20mm apart. Paint 34 eyepins black and fit them in the same way you placed the stern eyepins.

Take a grating that's already been made up or make one up and cut two sections 2 x 4 each then cut eight lengths of 2 x 3 x 300mm strip to frame the gratings. Paint the strips yellow ochre and fit them to the gratings. Next drill four holes in each frame with a 0.75 bit then paint 8 eyepins black and fit them to the gratings. Then glue the two finished gratings between the second and third row of gunwale eyepins at the bow.

Stage complete.

Store any unused parts in a labelled bag for future use .
arpurchase attached the following image(s):
P6184907.JPG
P6194910.JPG
P6194913.JPG
P6194914.JPG
P6194917.JPG
P6194920.JPG
P6194921.JPG
P6194924.JPG
P6194927.JPG
P6194930.JPG
P6194935.JPG
P6194937.JPG
P6194941.JPG
P6194944.JPG
Current builds:-C57,Zero, Lamborghini Countach, Caldercraft HMS Agamemnon,Robi,R2-D2, MFH Cobra .

arpurchase
#5 Posted : 20 June 2018 17:05:18

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsTurquoise Medal: Turquoise Medal for model making know-how contributionOutstanding Build: An award for an outstanding buildBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Registered

Joined: 27/09/2011
Posts: 15,196
Points: 45,687
Location: Dudley
Stage 95

Stage 95 contents:- Bowsprit parts, mast caps, yards, jibboom, eyepins, blocks and bowsprit plan.

Important Notice

From this stage forward, the numbers in the parts photos in the Stage PDF's refer to those listed on the supplied plans from Stages 95, 97, 101, 105. The diagrams will also be referred to in the steps. All details for parts needed are also listed on the plans.


Take the netting previously supplied and cut strips 7mm wide. Measure the front and rear bulwarks to obtain the lengths needed. Note for the stern nets you will need to cut four pieces per ships side. Starting at the bow glue the netting to the bulwark ends and the pins in between. The insides will take a single strip and the outers will be made of three parts one around the platform, one forward and one aft of the platform. Repeat the above on the other side of the ship.

Cut more lengths of net 7mm wide and fit it to both sides of the stern bulwarks in the same way you fitted the bow nets. Next take some 0.80 brown thread and pass four lengths through the eyepins at the bow bulwarks gluing the ends to the bulwark ends. Repeat this for the stern nets.

Now cut two more lengths of brown thread to go through the four midships eyepins gluing the thread ends to the inner bulwarks.

From Stage 74 remove the two bow parts from the fret and sand them smooth then file four grooves along the top of each part then add a piece of 2 x 2 x 300 strip along the top edge. Shape the strip to fit then paint the insides with the green you have used on the inner bulwarks and the outsides black. Glue both parts when dry to the bow gunwale with the ends half way across the forward port.

Stage complete.

Store any unused parts in a labelled bag for future use .
arpurchase attached the following image(s):
P6204950.JPG
P6215016.JPG
P6204952.JPG
P6204955.JPG
P6204956.JPG
P6204959.JPG
P6204961.JPG
P6204962.JPG
P6204967.JPG
P6204969.JPG
P6204970.JPG
P6204974.JPG
P6204975.JPG
P6204979.JPG
P6204982.JPG
P6204983.JPG
P6204985.JPG
P6204988.JPG
P6204989.JPG
P6204992.JPG
P6204999.JPG
P6205000.JPG
P6205003.JPG
P6205005.JPG
P6205006.JPG
P6205009.JPG
P6205012.JPG
Current builds:-C57,Zero, Lamborghini Countach, Caldercraft HMS Agamemnon,Robi,R2-D2, MFH Cobra .

arpurchase
#6 Posted : 21 June 2018 14:41:22

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsTurquoise Medal: Turquoise Medal for model making know-how contributionOutstanding Build: An award for an outstanding buildBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Registered

Joined: 27/09/2011
Posts: 15,196
Points: 45,687
Location: Dudley
Stage 96

Stage 96 contents:- Strapping, bracing line, netting, blocks, deadeyes, bees, jibboom, martingales and studdingsail booms.

Take the fret from Stage 68 and remove the three chocks and sand them smooth. Next cut three pieces of 2 x 3 x 300 strip to fit along the bottom of the chocks, glue the strips in place then stain the parts. Glue the three finished chocks along the centre of the midships grating. With a 0.75 bit drill four holes in the grating frame in line with the two end chocks. Glue an eyepin into each hole.

Retrieve the launch and place it onto the chocks then using thread tie the launch in place using the eyepins to retain the thread.

Open the bowsprit plans and lay the bowsprit over them and mark the angle where the cap will fit and then cut it to length. Shape the upper end of the bowsprit so there is a square block that will fit into the cap. Next taper the bowsprit so its 10mm at the base and 9mm at the angled end then glue the cap in place.

Stage complete.

Store any unused parts in a labelled bag for future use .
arpurchase attached the following image(s):
P6215028.JPG
P6215030.JPG
P6215034.JPG
P6215036.JPG
P6215040.JPG
P6215042.JPG
P6215043.JPG
P6215046.JPG
P6215049.JPG
P6215054.JPG
P6215056.JPG
P6215060.JPG
P6215064.JPG
P6215065.JPG
P6215070.JPG
Current builds:-C57,Zero, Lamborghini Countach, Caldercraft HMS Agamemnon,Robi,R2-D2, MFH Cobra .

arpurchase
#7 Posted : 23 June 2018 15:27:58

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsTurquoise Medal: Turquoise Medal for model making know-how contributionOutstanding Build: An award for an outstanding buildBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Registered

Joined: 27/09/2011
Posts: 15,196
Points: 45,687
Location: Dudley
Stage 97

Stage 97 contents:- Foremast and yard parts, foretop fret and foremast plan.

Using a 0.75 drill drill holes in the bulwarks at the midpoint between the gun ports then insert shortened eyepins into each hole do this on both sides of the bulwarks. Next make up three carronades so you have twenty in all. Cut enough 150mm lengths of 0.15 thread to service all the carronades then fit them to the gun ports starting at the stern and working forward. You should have 10 carronades on either side of the ship with a single gun port on both sides free at the bow.

Next take the 3 x 5 x 300 ramin strip from Stage 95 and using the bowsprit plan mark on the strip the length and the position of the steps. Proceed to cut the steps along the strip using the plan as a guide then when it is finished glue it in position on the bowsprit. Using the same strip of ramin make up the knee and again using the bowsprit plan cut and shape it to size and then glue it in position.

Next using the plan mark the 5 holes below the steps on the bowsprit and then use a 1.5mm bit to drill each hole. Smooth the steps and then use 0.80mm brown thread to create the bindings on the forward three holes.

Stage complete.

Store any unused parts in a labelled bag for future use .
arpurchase attached the following image(s):
P6215072.JPG
P6215082.JPG
P6215083.JPG
P6215089.JPG
P6235143.JPG
P6235099.JPG
P6235101.JPG
P6235103.JPG
P6235106.JPG
P6235112.JPG
P6235113.JPG
P6235116.JPG
P6235119.JPG
P6235121.JPG
P6235123.JPG
P6235127.JPG
P6235130.JPG
P6235133.JPG
P6235137.JPG
Current builds:-C57,Zero, Lamborghini Countach, Caldercraft HMS Agamemnon,Robi,R2-D2, MFH Cobra .

arpurchase
#8 Posted : 24 June 2018 17:51:26

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsTurquoise Medal: Turquoise Medal for model making know-how contributionOutstanding Build: An award for an outstanding buildBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Registered

Joined: 27/09/2011
Posts: 15,196
Points: 45,687
Location: Dudley
Stage 98

Stage 98 contents:- Foremast yard parts, Wire, crosstrees, deadeyes and blocks.

With a 5mm bit drill two holes one centrally in the white bow ribbon 10mm away from the stem and then drill one directly below it centrally in the black ribbon. Measure 10mm across from the lower hole just drilled to make three holes at the bow. Repeat the above on the other side of the bow.

Next take the frets saved from Stages 62 and 69 remove the parts and sand them smooth. Assemble the rails to the bulwarks making a left and right hand and then add a strip across the top using lengths of 2 x 5 x 300 strip. Paint all the assembled parts black and store then until there needed.

Take the fairlead from Stage 95 and cut it in half then using the bowsprit plan mark off the positions of the seven holes and then drill all seven using a 1mm bit. Glue the prepared fairlead to the bowsprit. Next cut six lengths of 2 x 2 mm strip and make the cleats then make up the bee blocks and bee's. Mark there positions and glue all the assembled parts in place on the bowsprit.

Next use the 6mm ramin dowel the make the jib boom, using the bowsprit plan cut and shape the boom until they both match. You will next need to shape the upper hole in the bit to the correct angle so the jib boom can pass through it. When everything fits glue the jib boom to the bowsprit assembly. Now cut and shape the martingales to match the plan and glue them together at the top.

Stage complete.

Store any unused parts in a labelled bag for future use .
arpurchase attached the following image(s):
P6245153.JPG
P6245162.JPG
P6245165.JPG
P6245167.JPG
P6245171.JPG
P6245177.JPG
P6245178.JPG
P6245184.JPG
P6245186.JPG
P6245187.JPG
P6245190.JPG
P6245193.JPG
P6245195.JPG
P6245196.JPG
P6245198.JPG
P6245203.JPG
P6245207.JPG
P6245208.JPG
P6245211.JPG
P6245213.JPG
Current builds:-C57,Zero, Lamborghini Countach, Caldercraft HMS Agamemnon,Robi,R2-D2, MFH Cobra .

arpurchase
#9 Posted : 25 June 2018 16:02:30

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsTurquoise Medal: Turquoise Medal for model making know-how contributionOutstanding Build: An award for an outstanding buildBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Registered

Joined: 27/09/2011
Posts: 15,196
Points: 45,687
Location: Dudley
Stage 99

Stage 99 contents:- Yard parts, boom irons, cleats and a crosstrees.

From Stage 65 take the fret and remove the two knees then cut two 20mm long pieces from a 6 x 6 x 300 strip. Glue these to the knees to make the catheads then with a 1mm bit drill four evenly spaced holes in the ends of the catheads and paint them black. Next drill four holes in the front face of the cathead and one below in the knee then glue 5 eyepins in place then add one more eyepin to the rear facing cathead side.

From Stage 69 clean up the ornaments and paint them white. When dry glue them to the cathead ends. Glue the catheads just below the bulwark rail and just behind the forward bulwark ends.

Take the Martingales assembled in the last stage and using the plan mark and drill the six holes then cut sixteen 4mm long pieces of 1mm brass rod and glue them in the indicated positions on the martingales as per the plans.

Next take some 1mm brass rod and make a boom iron to fit over the jib boom, when it is shaped correctly glue it in possition. Centre the martingale on the front face of the bowsprit cap and glue it in place then form a strap from 1mm brass rod and glue it over the martingale to hold it in position.

Stage complete.

Store any unused parts in a labelled bag for future use .
arpurchase attached the following image(s):
P6255218.JPG
P6255224.JPG
P6255227.JPG
P6255229.JPG
P6255233.JPG
P6255236.JPG
P6255239.JPG
P6255241.JPG
P6255247.JPG
P6255248.JPG
P6255250.JPG
P6255254.JPG
P6255257.JPG
P6255262.JPG
P6255263.JPG
P6255267.JPG
P6255269.JPG
P6255272.JPG
P6255273.JPG
P6255278.JPG
Current builds:-C57,Zero, Lamborghini Countach, Caldercraft HMS Agamemnon,Robi,R2-D2, MFH Cobra .

arpurchase
#10 Posted : 27 June 2018 16:48:09

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsTurquoise Medal: Turquoise Medal for model making know-how contributionOutstanding Build: An award for an outstanding buildBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Registered

Joined: 27/09/2011
Posts: 15,196
Points: 45,687
Location: Dudley
Stage 100

Stage 100 contents:- Main studdingsail booms, thread and blocks.

Take the beakhead assembly from Stage 77 and test fit it in place with the bow bulwarks from Stage 98, adjust the fit and glue the beakhead in place. Start to cut the struts under the beakhead to size and then paint them black. Next take the 0.5mm wire and cut it to length and then paint the wire white. When the paint is dry cut the wire to length and add a wire to each side of the strut then glue them in place. Do this for both sides of the beakhead.

Take the side bulwarks from Stage 98 then cut more 0.5mm wire to size and paint it white when the paint is dry glue the wire to the bulwarks, repeat the above for the other bulwark.

Using the bowsprit plan cut the flying jibboom to size and then shape it as indicated on the plan making sure you place the step at its front end. Next stain the flying jibboom and the jibboom forward of the cap with stain and allow to dry. Then paint the rest of the bowsprit white.

Stage complete.

Store any unused parts in a labelled bag for future use .

You can view the official video build for this pack here-


https://www.youtube.com/...e&index=11&t=0s
arpurchase attached the following image(s):
P6235144.JPG
P6265323.JPG
P6265326.JPG
P6265328.JPG
P6265329.JPG
P6265332.JPG
P6275338.JPG
P6275341.JPG
P6275345.JPG
P6275348.JPG
P6275351.JPG
P6275355.JPG
P6275362.JPG
Current builds:-C57,Zero, Lamborghini Countach, Caldercraft HMS Agamemnon,Robi,R2-D2, MFH Cobra .

Users browsing this topic
Guest
Forum Jump  
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.

Powered by YAF | YAF © 2003-2009, Yet Another Forum.NET
This page was generated in 0.305 seconds.
DeAgostini