Welcome Guest Search | Active Topics | Log In | Register

Robocop Official Build Pack 3 Options
Markwarren
#1 Posted : 19 November 2023 17:08:32

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsTurquoise Medal: Turquoise Medal for model making know-how contributionOutstanding Build: An award for an outstanding buildBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Registered, Administrators, Global Forum Support, Moderator, Forum Support Team, Official Builds

Joined: 04/01/2016
Posts: 6,242
Points: 19,013
Location: Northamptonshire, England
Issue 7

The Right Shoulder

Picture 1
shows the contents of this issue.
Assemble the outer right shoulder cover as shown in pictures 2 and 3.
Take the assembly you did in issue 6 and using 2 x CM screws attach it to the shoulder cover as shown in picture 4 and 5.

Picture 6 shows the final assembly for this stage.

That completes this issue.
Markwarren attached the following image(s):
7 (1).jpg
7 (2).jpg
7 (3).jpg
7 (4).jpg
7 (5).jpg
7 (6).jpg
Markwarren
#2 Posted : 22 November 2023 20:50:30

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsTurquoise Medal: Turquoise Medal for model making know-how contributionOutstanding Build: An award for an outstanding buildBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Registered, Administrators, Global Forum Support, Moderator, Forum Support Team, Official Builds

Joined: 04/01/2016
Posts: 6,242
Points: 19,013
Location: Northamptonshire, England
Issue 8

The Right Arm

Picture 1
shows the contents of this issue.
Fit the front arm cover onto the side of the inner cover as shown in picture 2. Apply a little pressure until the two pins clip into the holes. Picture 3 shows the attached assembly.
Next, align the assembly onto the arm assembly from issue 7. I found that lining up the centre hole and partially screwing in the GP screw slightly, helped with the alignment. Make sure the two pins slide into the holes as shown in picture 4. Picture 5 shows the assembly attached with the GP screw.

Picture 6 shows the final assembly for this stage.

That completes this issue.
Markwarren attached the following image(s):
8 (1).jpg
8 (2).jpg
8 (3).jpg
8 (4).jpg
8 (5).jpg
8 (6).jpg
Markwarren
#3 Posted : 27 November 2023 19:40:37

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsTurquoise Medal: Turquoise Medal for model making know-how contributionOutstanding Build: An award for an outstanding buildBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Registered, Administrators, Global Forum Support, Moderator, Forum Support Team, Official Builds

Joined: 04/01/2016
Posts: 6,242
Points: 19,013
Location: Northamptonshire, England
Issue 9

The Right Arm

Picture 1
shows the contents of this issue.
Insert the right forearm (9a) so that it fits with the two posts of the assembly you did in issue 8. Firstly, secure the bottom of this part with 2 x AP screws, picture 2.
Note: I had to jiggle it around a bit to get the screw holes lined up. Now secure the two posts with an CM screw one side and a CP screw the other side, this is again shown in picture 2.

Connect the middle right forearm, (9B) to the upper forearm, it should only fit one way. Secure with 2 x CM screws, picture 3.

Picture 4 shows the final assembly for this stage.
Markwarren attached the following image(s):
9 (1).jpg
9 (2).jpg
9 (3).jpg
9 (4).jpg
Markwarren
#4 Posted : 07 December 2023 20:43:22

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsTurquoise Medal: Turquoise Medal for model making know-how contributionOutstanding Build: An award for an outstanding buildBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Registered, Administrators, Global Forum Support, Moderator, Forum Support Team, Official Builds

Joined: 04/01/2016
Posts: 6,242
Points: 19,013
Location: Northamptonshire, England
Issue 10

The Right Arm

Picture 1
shows the contents of this issue.
Insert the wrist joint (10B) within (10A), making sure the thinner end of the part is inserted first. Now place the friction block (10D) over the smaller friction block (10E). Holding the assembly together, fit over the parts onto the wrist joint (10B) and hold in place whilst fitting the joint bracket, which only fits into one position, and securing the assembly with 3 x CP screws, pictures 2 and 3.

Attach this assembly onto the assembly you made in the previous issue, and secure with 3 x BP screws, picture 4.

Picture 5 shows the final assembly for this stage.

That completes this issue.
Markwarren attached the following image(s):
10 (1).jpg
10 (2).jpg
10 (3).jpg
10 (4).jpg
10 (5).jpg
Users browsing this topic
Guest
Forum Jump  
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.

Powered by YAF | YAF © 2003-2009, Yet Another Forum.NET
This page was generated in 0.202 seconds.
DeAgostini