|
|
Rank: Administration        Groups: Registered, Forum Support Team, Administrators, Global Forum Support Team, Moderator, Official Builds Joined: 09/11/2012 Posts: 8,191 Points: 23,661 Location: East midlands
|
Hi All, 
This is the start of the next pack which will cover Issues 95 - 98. 
Well, the end is in sight for the main build of Ironman`s Armour with him standing straight up. (Position A)
In this first update (Issue 95) we will continue building the Abdominal section for Position B, where Ironman will be posed with the upper body twisted slightly to one side. NOTE: In the instructions at the end of issue 95 it states that the position B abdomen is complete, but that is incorrect as it is not completed until the first stage of issue 96. (Coming soon)
Parts supplied for this issue are shown in Pic 1. You will also need the assembly from the last update Issue 94.
Start by positioning the left side plate (95C)to the front abdominal armour (95D) as shown in Pic 2, then secure the parts together with the use of an LP screw as in Pic 3.
The Internal Connection Support (95E) is now placed into the inside of the previous parts and secured by 2 x IP screws. Pic 4.
Time now to bring the Issue 94 assembly to the work space and slide it inside the the parts just assembled. Pic 5. Then whilst carefully holding the parts in position, turn them over and fix them together using an LP screw. Pic 6.
The right side plate (95B) is now put into position, Pic 7 and is fixed by the use of an LP screw. Pic 8.
Finally, slide the Abdomen/Chest Connector (95A) into the assembly and fix it with 2 x UP screws. Pic 9.
That completes this stage of Abdomen B, Pic 10, which will be completed in the first stage of Issue 96. More on that when I post up Issue 96. 
Regards
delboy271155
(Derek) Admindelboy271155 attached the following image(s): COME BACK GUY FAWKES "YOUR COUNTRY NEEDS YOU"
|
|
|
Rank: Administration Groups: Registered, Forum Support Team, Administrators, Global Forum Support Team, Moderator, Official Builds Joined: 09/11/2012 Posts: 8,191 Points: 23,661 Location: East midlands
|
|
|
|
Rank: Administration Groups: Registered, Forum Support Team, Administrators, Global Forum Support Team, Moderator, Official Builds Joined: 09/11/2012 Posts: 8,191 Points: 23,661 Location: East midlands
|
Hi All,
Here we are with the second instalment of Issue 96. Due to the size of this stage it is posted in two parts.
In this update we will be building The Hips.
HIPS (Part 1)
In Pic 1: I have shown the parts that will be used in this update including parts left over from Issue 96 and parts that have been stored from previous issues.
Recover the parts from Issues 71 and 33 that are marked with an "L" Pic 2 and fit a friction ring (96G) inside the socket from Issue 33, Pic 3.
Now position the socket and friction ring onto the ball of part 71B. Lift the ring under the ball and make sure that the pin on the socket locates correctly into the lower ring and then fix them together using 4 x KP screws, Pic 4. Note: Locate all four screws in position and then tighten them equally in turn. Tighten them enough so that the ball and socket joint is stiff, but can still be moved.
Now recover the same parts, but marked with an "R" and fit a friction ring 96G into the socket. Pic 5. Then assemble the ball and socket joint as before using 4 x KP screws. Pic 6.
Bring both ball and socket joints to the table, Pic 7, then place them together and fix them in place using 3 x LP screws Pic 8. Warning: The instructional booklet indicates an incorrect place to fit one of the LP screws. Pic 8 is correct.
The instructions now tell you to wrap the internal tabs of part 71a with double sided tape. I tried the fit of my part first and found that it stayed in place without the need for tape. If your part fits loosely then use the tape. Pic 9 shows the armour plate correctly positioned and concludes Part 1 of this update.
Part 2 coming very soon.
Regards
delboy271155
(Derek) Admin delboy271155 attached the following image(s): COME BACK GUY FAWKES "YOUR COUNTRY NEEDS YOU"
|
|
|
Rank: Administration Groups: Registered, Forum Support Team, Administrators, Global Forum Support Team, Moderator, Official Builds Joined: 09/11/2012 Posts: 8,191 Points: 23,661 Location: East midlands
|
|
|
|
Rank: Administration Groups: Registered, Forum Support Team, Administrators, Global Forum Support Team, Moderator, Official Builds Joined: 09/11/2012 Posts: 8,191 Points: 23,661 Location: East midlands
|
|
|
|
Rank: Administration Groups: Registered, Forum Support Team, Administrators, Global Forum Support Team, Moderator, Official Builds Joined: 09/11/2012 Posts: 8,191 Points: 23,661 Location: East midlands
|
Hi All,
This is the final update for Issue 96, where we will connect the legs to the hip joints. This will be in two parts, but the process is the same for both the right and left legs. Part 1 will show the right leg and very soon after Part 2 will show the left.
PART 1:
In Pic 1, I have shown all the parts you need to gather together for this update. The parts from this issue (96) are the double sided tape strips, GP and IP screws.
Start by positioning the right side of the hip joints into the slot on the inside of the right leg. Pic 2. NOTE: Take care to avoid damage to the felt disc. Then place the Inner Thigh Structure (57A) in place and secure it with 4 x GP screws. Pic 3.
Bring in the gold/red part from Issue 55. Test fit this part on the rear of the right leg and if it is a loose fit, then wrap a double sided piece of tape around each of the locating tabs and refit. Pic 4.The inner thigh plate (55A) is now pressed into place. Pic 5. NOTE: The locating pins are very small so take extra care when installing this part.
We now turn to the front of the right leg and position part (56B) in place and fix it using 2 x IP screws. Pic 6. Finally with care, press part 56C into place Pic 7.
That concludes the attachment of the right leg and Part 1 of this update. Pic 8.
See you very soon for part 2 - connecting the left leg that will conclude Issue 96.
Regards
delboy271155
(Derek) Admin delboy271155 attached the following image(s): COME BACK GUY FAWKES "YOUR COUNTRY NEEDS YOU"
|
|
|
Rank: Administration Groups: Registered, Forum Support Team, Administrators, Global Forum Support Team, Moderator, Official Builds Joined: 09/11/2012 Posts: 8,191 Points: 23,661 Location: East midlands
|
Hi All,
This is the final update for Issue 96, where we will connect the left leg to the hip joints.
PART 2:
In Pic 1, I have shown all the parts you need to gather together for this update. The parts from this issue (96) are the double sided tape strips, GP and IP screws.
Start by positioning the left side of the hip joints into the slot on the inside of the left leg. Pic 2. NOTE: Take care to avoid damage to the felt disc. Then place the Inner Thigh Structure (38A) in place and secure it with 4 x GP screws. Pic 3.
Bring in the gold/red part from Issue 36. Test fit this part on the rear of the left leg and if it is a loose fit, then wrap a double sided piece of tape around each of the locating tabs and refit. Pic 4.The inner thigh plate (36A) is now pressed into place. Pic 5. NOTE: The locating pins are very small so take extra care when installing this part.
We now turn to the front of the left leg and position part (37B) in place and fix it using 2 x IP screws. Pic 6. Finally with care, press part 37C into place Pic 7.
That concludes the attachment of the left leg and Issue 96 updates. Pic 8.
Issue 97 will be coming soon and will include making some parts for the abdomens for poses C and D. PLUS IRONMAN WILL BE COMPLTE FOR POSE A (standing straight)
See you soon.
Regards
delboy271155
(Derek) Admindelboy271155 attached the following image(s): COME BACK GUY FAWKES "YOUR COUNTRY NEEDS YOU"
|
|
|
Rank: Administration Groups: Registered, Forum Support Team, Administrators, Global Forum Support Team, Moderator, Official Builds Joined: 09/11/2012 Posts: 8,191 Points: 23,661 Location: East midlands
|
Hi All,
Well, here we go with Issue 97`s update.
First, we will be the building two identical assemblies that will be part of the Abdomens for Pose C and D.
Then, IRONMAN POSE "A" (Standing Upright) will be completed. 
Parts ..... Pic 1.
As these two assemblies are identical, I`ll only show one for obvious reasons.
You have been supplied with two left and two right sides for these assemblies, so start with a left side part, Pic 2. Then position a spring onto a spring base and orientate as in Pic 3. Now take the spring and base and position them as shown in Pic 4, making sure the spring (yellow arrow) the pivot (blue arrow) and the catch (black arrow) are in the correct positions.
Now carefully position a right side of the assembly in place (marked "R") on top of the assembly so far. Ensure that the pivot of the spring base is correctly placed and secure the parts together using 3 x LP screws. . Pic 5
That completes the first assembly, so repeat the previous steps and produce the second. Pic 6.
HERE WE GO, LET`S GET IRONMAN "Pose A" FINISHED:
Bring in Pelvic Base "A" and push it into place until it clicks into place with the hip joints. Pic 7.
NOW PLEASE TAKE CARE: two LP screws now need to be used to lock the pelvic unit in place. You will need to move some of the hinged plates and manipulate the leg/hip joints on either side to fit these screws. Pic 8.
You now have the top and bottom halves of Ironman complete and just need to press the two halves together as shown in Pic 9. Note: No force should be needed if the halves are correctly aligned and you should hear a "click" when they are attached.
Tips for displaying Ironman in Pose "A" (standing):
Make sure the upper body is straight above the legs.
The body clamp of the stand should be around the lower rib area.
If you move the arms out from the body, you may need to adjust the position of the feet to keep the correct balance.
Just be sure that you keep hold of the model until it is balanced as needed.
Pics 10 - 12 show how my Pose "A" finished up. NOTE: the observant ones will see that I have not placed the screw covers into the top of the chest plate. The reason being that they have to come out in future issues. When I eventually decide which pose and armour I prefer, then I will put them in place.
I won`t be leaving you here, I will continue through Pose "B","C" and "D" Issues 98 - 100 and the further through the battle damaged armour covered by Issues 101 - 120.
Watch this space and the "Finished Build" thread coming soon..
Regards
delboy271155
(Derek) Admin delboy271155 attached the following image(s): COME BACK GUY FAWKES "YOUR COUNTRY NEEDS YOU"
|
|
|
Rank: Administration Groups: Registered, Forum Support Team, Administrators, Global Forum Support Team, Moderator, Official Builds Joined: 09/11/2012 Posts: 8,191 Points: 23,661 Location: East midlands
|
|
|
|
|
Guest
|
UK
