|
|
Rank: Administration        Groups: Registered, Forum Support Team, Administrators, Global Forum Support Team, Moderator, Official Builds Joined: 09/11/2012 Posts: 8,193 Points: 23,667 Location: East midlands
|
|
|
|
Rank: Administration Groups: Registered, Forum Support Team, Administrators, Global Forum Support Team, Moderator, Official Builds Joined: 09/11/2012 Posts: 8,193 Points: 23,667 Location: East midlands
|
|
|
|
Rank: Administration Groups: Registered, Forum Support Team, Administrators, Global Forum Support Team, Moderator, Official Builds Joined: 09/11/2012 Posts: 8,193 Points: 23,667 Location: East midlands
|
|
|
|
Rank: Administration Groups: Registered, Forum Support Team, Administrators, Global Forum Support Team, Moderator, Official Builds Joined: 09/11/2012 Posts: 8,193 Points: 23,667 Location: East midlands
|
Hi All, 
Here we are with the second part of Issue 44, where the build of the "standard" base begins. You will need to gather the three upper base parts and the three lower base parts, along with the type 02 screws from this issue.
As I have not been gifted with three hands, I changed my approach to the assembly of the three top parts.
Take the two upper parts with logos on, locate the pins of one into the holes of the other and press them together. Pic 1. Then feed the third upper part in as shown in Pic 2. Locating all the pins into holes, gradually twist and press the joints together as shown in Pic 3 and 4.
Now flip the base over and secure the three parts using 12 x 02 type screws. Pic 5.
Keeping the base in the same position, put the three lower base parts in place and secure them with a further 9 x 02 type screws as in Pic 6.
That concludes this part of Issue 44 Pic 7, with Issue 45 coming soon.
Regards
delboy271155
(Derek) Admindelboy271155 attached the following image(s): COME BACK GUY FAWKES "YOUR COUNTRY NEEDS YOU"
|
|
|
Rank: Administration Groups: Registered, Forum Support Team, Administrators, Global Forum Support Team, Moderator, Official Builds Joined: 09/11/2012 Posts: 8,193 Points: 23,667 Location: East midlands
|
Hi All,
Update time for the Gaunlet with Issue 45.
In this issue we will add parts to the "standard base". The parts supplied for the "POWER" stone will be used in the update for Issue 46.
Parts supplied.....Pic 1. You will also need the base from issue 44.
Start by pressing the part "base 03" into the centre of the top side of the base platform. Pic 2.
Whilst holding the upper part in place press the lower part of the centre section "base 04" into place and fix the centre parts using 6 x type 02 screws. Pic 3. Then keeping the base upside down stick the EVA pads in place over the screw holes. Pic 4.
That`s it for this update. Pic 5.
In the next update we will build the Power stone.
See you soon. 
Regards
delboy271155
(Derek) Admindelboy271155 attached the following image(s): COME BACK GUY FAWKES "YOUR COUNTRY NEEDS YOU"
|
|
|
Rank: Administration Groups: Registered, Forum Support Team, Administrators, Global Forum Support Team, Moderator, Official Builds Joined: 09/11/2012 Posts: 8,193 Points: 23,667 Location: East midlands
|
Hi All,
Well, here we are at the end of another pack. Update time for Issue 46.
In this update we will build the "Power" stone.
Parts supplied.....Pic 1. You will also need the two parts not used from Issue 45 and the back of the hand section of the Gauntlet.
Start with the base section of the stone (C73), position the circuit board (Elec 04) inside and fix it in place using 2 x type 01 screws. Pic 2. Now place the two springs over the relevant posts as in Pic 3.
Next retrieve the stone and its surround from the previous issue. Place the stone as shown in Pic 4, place the surround over the stone Pic 5 and then whilst holding the parts together, secure them by the use of 2 x type 01 screws from beneath. Pic 6.
Take the supplied LR41 batteries and put them into the battery holder. Make sure the polarity is correct on all three, with the + sides towards the spring. Pic 7. Now position the battery cover and fix it in place using a type01 screw. Pic 8.
Next place the two parts D02 (without the magnets in them)over the magnets in the base of the stone and secure them with 4 x type 01 screws. Pic 9. Now fix the two parts D02 (ones with the magnets) into the right hand recess in the Gauntlet and fix them with a further 4 x type 01 screws. Pic 10.
Fit and test the Power stone. Pic 11.
That concludes this update and finishes this pack. Pic 12.
See you as soon as the next pack arrives.
Regards
delboy271155
(Derek) Admindelboy271155 attached the following image(s): COME BACK GUY FAWKES "YOUR COUNTRY NEEDS YOU"
|
|
|
|
Guest
|
UK
