Welcome Guest Search | Active Topics | Log In | Register

BTTF Delorean Official build STAGES 22 - 26 Options
roymattblack
#1 Posted : 09 July 2024 17:53:14

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsOutstanding Build: An award for an outstanding buildBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered

Joined: 04/06/2011
Posts: 4,280
Points: 12,991
Location: ipswich
STAGE 22A:

These parts will allow you to continue assembling more of the engine detail.

Locate the bracket and cover, parts22A and 22B.
Clip the parts together. They will only fit one way.
Fit the assembly to the transmission end of the engine and secure using 1 x MM screw.

Locate the thermostat housing, part 22E and fix it to the top of the front of the engine using 2 x AP screws.
The housing will only fit one way.

Locate the throttle control and support arm, parts 22C and 22D.Fit the parts together and fix using 1 x AP screw from underneath.

Fit this assembly to the top of the thermostat housing and fix using 1 x AP screw.

Locate the fuel distributor and control unit, parts 22F and 22H.
Fit the two parts together and fix from underneath using 2 x AP screws.
roymattblack attached the following image(s):
P1014337A.jpg
P1014339A.jpg
P1014340A.jpg
P1014341A.jpg
P1014342A.jpg
P1014343A.jpg
P1014344A.jpg
P1014347A.jpg
P1014348A.jpg
P1014350A.jpg
P1014351A.jpg
P1014352A.jpg
P1014353A.jpg
roymattblack
#2 Posted : 09 July 2024 17:59:44

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsOutstanding Build: An award for an outstanding buildBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered

Joined: 04/06/2011
Posts: 4,280
Points: 12,991
Location: ipswich
STAGE 22B:

Locate the mixture control housing, part 22I.
Fit the previous assembly to the top of the unit and secure from underneath using 1 x AP screw.
The parts will only fit together one way.

Locate the intake manifolds, part 22J and fit it to the end of the previous assembly.
The parts will only fit together properly one way.
Fix together using 2 x AP screws.

Fit this assembly to the ends of the air boxes on the top of the engine and secure using 4 x AP screws.

Locate the 6 x small injector fittings, parts 6 x 22G.
Press three in each side of the fuel injector plate, part 22F, previously installed.

Make sure the fittings on each side, point outwards.
TAKE CARE not to lose one of these tiny parts. There is no spare included.

Locate the 6 x fuel lines.
They are in pairs according to length.

The short pair are parts 2 x 22K
The middle length are parts 2 x 22L
The long pair are parts 2 x 22M.

Fit these lines to the small pins on the inside upper edge of each cylinder head.
The other end of the lines attach to the 6 x injector fittings, parts 6 x 22G.

When fitting the lines, start with the shortest which go to the transmission end of the engine.
The long lines fit at the front end and the middle length lines go in the centre.

Store this assembly safely for now.

roymattblack attached the following image(s):
P1014354A.jpg
P1014355A.jpg
P1014356A.jpg
P1014357A.jpg
P1014358A.jpg
P1014359A.jpg
P1014360A.jpg
P1014361A.jpg
P1014362A.jpg
P1014364A.jpg
roymattblack
#3 Posted : 10 July 2024 13:38:55

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsOutstanding Build: An award for an outstanding buildBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered

Joined: 04/06/2011
Posts: 4,280
Points: 12,991
Location: ipswich
STAGE 23A:

These parts will allow you to continue assembling even more of the engine detail.

Retrieve the main engine assembly.

Locate the mounting bracket, part 23D.
Fix to the right upper front side of the engine using 2 x AM screws.

Locate the alternator parts, 23B and 23C.
NOTE: These parts are incorrectly called the distributor in the printed instructions.
Fit the two parts together and fix with an AP screw at one end.

OPTIONAL DETAIL:
To improve the appearance of the alternator, you can fit a strip of black tape around the recessed centre section.
This is entirely at the builder’s discretion.

Fit the alternator to the engine bracket using 2 x AP screws.
roymattblack attached the following image(s):
P1014365A.jpg
P1014366A.jpg
P1014367A.jpg
P1014368A.jpg
P1014369A.jpg
P1014370A.jpg
P1014372A.jpg
roymattblack
#4 Posted : 10 July 2024 13:41:42

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsOutstanding Build: An award for an outstanding buildBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered

Joined: 04/06/2011
Posts: 4,280
Points: 12,991
Location: ipswich
STAGE 23B:

Locate the other mounting bracket, part 23A.

OPTIONAL DETAIL:
You can colour the recessed area with black paint to make it look like an open slot.
This is entirely at the builder’s discretion.

Fit the bracket to the end of the alternator and the engine and fix with 1 x AM screw.

Locate the dipstick, part 23G.
NOTE: This is incorrectly labelled 22K in the printed instructions.

Fit the dipstick in place, locating the end in the hole in the engine sump.

Locate the two gearbox mounting brackets, parts 23E and 23F.
Fit 23E to the left side of the gearbox and 23F to the right side.
Secure the parts with 2 x DM screws in each bracket.

Store the engine safely for now.

roymattblack attached the following image(s):
P1014373A.jpg
P1014374A.jpg
P1014376A.jpg
P1014377A.jpg
P1014378A.jpg
P1014379A.jpg
P1014382A.jpg
P1014383A.jpg
roymattblack
#5 Posted : 11 July 2024 17:19:59

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsOutstanding Build: An award for an outstanding buildBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered

Joined: 04/06/2011
Posts: 4,280
Points: 12,991
Location: ipswich
STAGE 24A:

These parts will allow you to build the engine pulleys and belts.

Retrieve the main engine assembly.

All of the pulley parts are marked with the corresponding part letter making identifying each one easy.

Locate the pulley parts 24A, 24B and 24C.
They fit on the lower central shaft on the front of the engine in the order 24C, 24B and finally 24A.
The parts are then fixed using 1 x AM screw.

Locate the next pulley parts, 24D and 24E.
These fit on the post directly above the one you just used.
24D goes on first, then 24E.
Fix them in place with 1 x AP screw.
roymattblack attached the following image(s):
P1014416A.jpg
P1014418A.jpg
P1014420A.jpg
P1014421A.jpg
P1014422A.jpg
P1014423A.jpg
P1014424A.jpg
P1014425A.jpg
roymattblack
#6 Posted : 11 July 2024 17:23:26

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsOutstanding Build: An award for an outstanding buildBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered

Joined: 04/06/2011
Posts: 4,280
Points: 12,991
Location: ipswich
STAGE 24B:

Locate the alternator rotor, part 24F.
This fits onto the end of the alternator shaft.
Locate pulley part 24G and fit this over the alternator rotor and fix using 1 x AP screw.

Locate the two pulley parts, 24H and 24I.
Press the two parts together.
They will only fit one way.
Fit this assembly to the end shaft of the AC unit and fix in place with 1 x AP screw through the hole in the end of the pulley.

Locate the two rubber belts, 24J and 24K.
Both belts are actually the same.

Fit belt 24J over the central two pulleys and the alternator pulley.
Fit belt 24K over the lower central pulley and the AC unit pulley.

Store the engine safely for now.
roymattblack attached the following image(s):
P1014426A.jpg
P1014427A.jpg
P1014428A.jpg
P1014429A.jpg
P1014430A.jpg
P1014431A.jpg
P1014433A.jpg
P1014434A.jpg
P1014435A.jpg
Users browsing this topic
Guest
Forum Jump  
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.

Powered by YAF | YAF © 2003-2009, Yet Another Forum.NET
This page was generated in 0.394 seconds.
DeAgostini