Also received stages 84, 88, and 89, which were put into the storage box in original packaging
The second front Ohlins fork is fully assembled
A new front fork Ohlin's decal has been applied
Brake caliper seals are painted in Tamiya gloss black
A new Brembo caliper decal has been applied
The correct color of adjusting nuts on the front suspension
The suspension top adjuster nut is painted in Tamiya gloss yellow
The suspension bottom adjuster nut is painted in Tamiya gloss black
Triple trees fitted and screwed up very tight
Fitting front tire to rim
Place the tire in a large bowl
Boil kettle
Pour hot boiling water into the bowl with the front tire fully submerged to make
Time for 5 minutes
Drain off all excess hot water
Fit tire to rim
Fit two-wheel disc with correct rotational arrows followed by wheel rim rotation
The first two parts of the exhaust system
second two parts of the exhaust system
exhaust muffler
All Screwed together very tight
The gaps were filled in with Humbrol model filler
Sanded smooth with a nail Henry board 180/240 grit
Then 3 coats of Tamiya Flat aluminum were applied
The exhaust muffler and inside the muffler were sprayed in matt black
The Exhaust muffler grille is now painted Tamiya Matt black
All exhaust flexi springs installed and fitted
Exhaust flexi spring mounts are painted in Tamiya dark copper
All O2 lambda sensors fitted and installed
A New Akrapovic muffler decal has been applied
A New Akrapovic Titanium decal has been applied
The front fender has been fitted to the front suspension mounts
Front axle secured in place
Tyre soft compound white stripe decals have been applied
Tyre yellow dot applied via a fine Sharpie permanent marker dipped into Tamiya yellow paint
Dash is completely assembled, and the warning light is painted in Tamiya red
The rear of the dash led transparent plastic Panel has been painted in Tamiya Red, Orange, and Dark Green paint to simulate Rev lights
Dash had 3 coats of clear satin varnish
A new part work upgrade Dash decal has now been applied
The cylinder head cover assembled
Cylinder head painted Tamiya dark blue
all exposed cylinder cover bolts are painted Tamiya gloss silver
Carbon fiber air box with pack 5 fully assembled and 3 coats of clear and polished high-gloss wax
Michelin tire bar codes large and small have been applied
Tire-soft compound white stripes have been applied
Marchesini racing wheel rim decals have been applied
A forged magnesium decal with an Italian flag 3-color stripe has been applied
A new custom-made FGR decal has been applied
A new matching custom-made OHLINS decal has been applied
A new MRA screen decal has been applied
A new radiator decal has been applied
c/o
www.febur.itAll coolant hoses to match the full race set
see the attached images below
A new panel display to match the Chrome L2M display needs to be applied
WWW.L2M.ITSee image below
A fresh coat of satin clear varnish is to be applied to the front wheel
Fit the front wheel
Stages 22 to 26 of the engine have been assembled
The cylinder head cover from the earlier issue was also used as part of the assembly process
Both crankshaft protective covers have had 3 coats of clear applied
The cylinder head block was painted in Tamiya XF-56 metallic grey so it resembles a cast cylinder head
The clutch slave cylinder and oil filter have also received 3 coats of clear
A heavy-duty screwdriver was used in this assembly process size PH1
A complete full set of tweezers was used as part of this assembly process also
An oil filter custom-made decal has been applied
In pack 7 detailing I have done and completed the:-
Water coolant pipe top fitting painted in Tamiya gun metal grey
Water coolant pipe scratches touched up by silver pen
Water pump front housing in Tamiya gloss black
Water pump done in chrome by using a chrome pen and fine-detail brush
The oil sump has been painted in Tamiya flat black
Oil sight glass was glued in place
Oil viewing sight glass has been dyed in light yellow to resemble oil
The edge of the oil sump touched up in Tamiya chrome silver
The timing chain cover was glued in place and given 3 coats of clear applied
All other black parts in pack 7 were given 3 coats of clear applied
Oil blue refill plugs were fitted and had 3 coats of clear applied
custom-made water slide decal in “ THE DOCTOR “ logo to go on the bottom left of the dash binnacle has now been applied
Clutch center and outer adjusting spring plate painted in Tamiya gold leaf
Starter motor mounting painted in Tamiya grey metallic
Fuel injection rail painted in Tamiya chrome silver
An air filter is fitted and installed and a custom MWR race air filter and water slide decal have been applied
A new fuel tank decal has been applied
Fuel tank black 3mm foam self-adhesive pad installed and fitted and applied
A new screen water slide decal has now been applied
Exhaust fittings painted Tamiya gun metal grey
90-degree banjo fitting nut painted in Tamiya blue and all AN fittings painted in Tamiya Red
Compressed air tank and mounting touched up with Tamiya Matt black
Ohlin’s shock absorber spring decal has been applied
Compressed air tank fitted
2 x black silicone hoses fitted to compressed air tank
A starter motor decal has been applied
Scrutineer certification decal applied to the left side of the frame
The rider medical certification decal applied to the left side of the frame
A new MRA clear vinyl decal has been applied to the screen
The chassis heads of screws have been painted in Tamiya gloss black
A technical control decal has been applied to the left side of the frame
B700 adhesive glue was used to glue the screen to the front upper fairing, very strong & crystal clear
Dash console display given two coats of clear gloss varnish spray
I purchased it from eBay Seller
1 x rear wheel
1 x rear tyre
1 x rear disc
1 x rear wheel axle
Rear wheel had 3 coats of clear gloss
The rear tire was soaked in a deep bowl of boiling water for 5 minutes and then fitted to the wheel rim
The rear disc was glued and fitted into place
The rear disc nuts have been painted in Tamiya black
The disc fittings were painted in gloss copper
Yellow dot applied to tire opposite the valve using Tamiya yellow
Soft compound decals have been applied
Small and large tire bar code decals have been applied
Forged aluminum with an Italian flag color stripes decal has been applied to the rim edge
A good coat of tyre dressing
I purchased it from eBay Seller
1 x rear subframe
1 x rear fender
1 x rear caliper
1 x rear brake disc speed sensor
2 x Michelin logo vinyl decals have been applied
4 x rear axle torque markings in water slide decal have been applied
1 x additional DID water slide decal has been applied to the rear swingarm
All are now fully assembled
All other additional works
All heads of screws and Allen bolts have had their heads painted in Tamiya gloss Black paint
The rear caliper has been painted in Tamiya aluminum paint
A new 5mm Brembo logo water slide decal has been applied to the rear caliper piston
3 lower holes to the lower part of the swingarm have been filled in with Humbrol model filler and sanded smooth then painted in Tamiya gloss black paint
The rear brake disc speed sensor inner hole has been filled in with Humbrol model filler and sanded smooth then painted in Tamiya gloss black paint
The rear seat cowl assembly was ordered from an eBay Seller
The top section of the seat cowl has had Yamaha logo in metallic gold self-adhesive vinyl decal
Top and both sides assembled
Rear tail light assembly and Lense put in place
A lower section was put in place
Then screwed together
Lower section screw heads painted in Tamiya gloss black
Upper section screw heads painted in Yamaha blue
The rear axle motorcycle axle stand was purchased from eBay
Wheel centres are painted with Tamiya gloss black paint
Wheel center nuts have been done with a metallic chrome pen
Tyres given 3 coats of Tamiya red paint
A dark blue extra fine-tip Sharpie pen has been ordered to touch up screw heads in blue
The front sprocket has now been fitted and installed and painted in Tamiya gun metal paint
The radiator cap GYTR vinyl decal has now been applied
speed sensor rear rotor decal has now been applied
The top coolant hose has been painted Samco Blue
1:4 scale TREMONIA jubilee clip fitted these were purchased from eBay UK
Race seats R1 logo decal has been applied
GB Racing engine protector decals have been applied
The rear lens red self-adhesive covering film has been applied
Samco hose decal has been applied
Rear axle torque mark decals have been applied on both sides
Tamiya 2.6mm braided brake line has been fitted to replace black silicone tubing brake lines ( rear brake lines )
The rear shock absorber cartridge has been assembled and installed
TTX decal has been applied to rear shock absorber cartridge
The rear shock absorber linkage assembly has been assembled and installed
The rear swing arm assembly that was purchased from an eBay seller and assembled has now been installed and fitted
Rear swing arm nut covers fitted and installed
Frame nut covers installed and fitted
Exhaust installed and support bracket installed and fitted
Radiator hoses installed
Rubber hoses painted Samco blue
Samco sport decals have been applied
Radiator installed and fitted
The bottom radiator support bracket was installed and fitted
Lamba sensors have been installed and fitted
Hydraulic pipework parts installed
Frame brackets installed
Mass air sensor cable installed and fitted to the top of carbon fiber Airbox using 2.6mm Tamiya braided hose with red heat shrink tubing and black heat shrink tubing on the other end and glued and sealed in place using B700 clear gel glue
File Attachment(s):
MASTER-BUILDER attached the following image(s):